Selection and planning
Pearl: how to set up a pedicure station with a pull-out basin
Perle doesn’t need a water connection, but it does need a plan: where you fill the basin, how you carry it, how much space the extended module takes up, and where you sit. We provide a ready-to-use water setup and workstation layout that works even next to a manicure desk.

The shortest answer
Perle works without a water hookup because its basin is removable: fill it at the sink, place it in the extended module, and after the treatment, take it out, empty it, and wash it. To avoid running back and forth, the sink should be just a few steps away, leave a metre in front of the chair for the extended module and your stool, and tuck the module away between appointments so the chair takes up less space.
Perle is our pedicure chair for salons without a water connection at the station: in rented premises, in an area next to the manicure station, or in treatment rooms that might look different a year from now. But no plumbing doesn’t mean no water, just different logistics. Below, we provide a ready-to-use workflow and station layout that works for our clients.
How does the pull-out basin module work?
Under the Perle seat is a module that you pull forward before the treatment. W the module is a removable basin: you take it out, fill it with warm water at the sink, put it back, and the client rests her feet on the adjustable support or immerses them in the water. After the treatment, you remove the basin, empty the water, wash and disinfect it, then slide the module under the chair.
This means the chair has two outlines: a stowed one, where it looks like an upholstered armchair, and an in-use one, extended by the pull-out module. W the treatment room layout, use the second one. The chair's weight capacity is 200 kg.
How do you plan water flow without a hookup?
- Sink within reach. Ideally in the same room or just behind a door, with no stairs. A full basin weighs several kilograms and splashes.
- Clear path. Don’t leave a trolley, chair, or client’s bag between the sink and the chair.
- Space for a clean basin. After washing, the basin dries away from the chair, for example on a shelf by the sink, and goes back into the module before the next appointment.
- Time. Filling, carrying, and washing the basin take a few minutes; include this in the appointment length so the next client doesn’t have to wait.
If the sink is far away or up a flight of stairs, consider a chair with a drainage pump, such as Noémie; we explain the differences in Noémie or Perle.
How much space does a Perle station need?
Leave about a metre in front for the extended module, your wheeled chair, and your knees. Keep one side clear for the client to get onto the chair. On the other side, place a wheeled trolley within arm’s reach. Altogether, you’ll need about 180 × 220 cm, depending on whether the trolley is beside or behind you.
If the Perle is next to a manicure desk, check that the extended module doesn’t block the desk drawers or the manicure client’s chair. The easiest option is to angle the chair so the module extends toward the open floor, not toward the other station.
What does the technician sit on at the Perle?
At a low chair, the client’s foot in the basin is just above the floor, while on the footrest it’s several dozen centimeters higher, so you sit at 40–50 cm and adjust the height during the treatment. Serenity (40–54 cm) with armrests or Essence (45–60 cm) work best; the Selle saddle starts at 45 cm, but it’s too high for use with the basin.
Position the trolley on your dominant-hand side, with tools on the top shelf and towels below. A rolling trolley can be moved out of the way when you extend the module. A matching chair, stool and trolley are available in the pedicure salon furniture category, and we explain how to choose the right chair height in our article on adjusting chair height.
How to clean Perle between clients?
Wash and disinfect the basin at the sink with a product suitable for surfaces that come into contact with water, wipe the module dry, and clean the upholstery with a product approved for faux leather. Water that drips onto the seat or armrest won't cause damage if you wipe it off; it can cause damage if it stays in the seams overnight.
Once a week, clean the upholstery with foam and apply a protective treatment, just as you would with a bed: faux leather used for pedicures comes into contact with water, oils and foot-care products—in other words, everything that dries it out. We describe the full routine in our guide to cleaning faux leather.
Checklist before your first client
- Keep the sink within reach and the path to it clear.
- Clear one metre of floor space in front of the chair when the module is extended.
- Keep one side clear for getting into the chair.
- Set the stylist's chair to 40–50 cm.
- Position the trolley on your dominant-hand side, where it won't get in the way when you extend the module.
- Keep towels, basin disinfectant and an upholstery cloth close at hand.
- Read the module instructions: the order for extending it and using the lock.
Frequently asked questions
Does Perle really not need any connections?
It doesn't need one. You carry the water in the removable basin, and the chair doesn't require electricity either.
How much water does the basin hold?
Enough to cover the feet up to the ankles. The exact capacity is listed on the product page.
Can I store the module with a full basin?
No, first remove and empty the basin. Store the module empty and dry.
Does Perle come in the same colours as the beds?
Yes, it comes in twelve faux leather colours, so you can match it to your chair and trolley.
